Beginner's Guide-3 Core Operating Standards for Floating Crane Lifting, Slewing, and Lowering

Nov 27, 2025

Leave a message

Lifting Operation: Stable Start, Overload Prevention


1. Pre-Lifting Inspection and Preparation

  • Operators must verify the floating crane's rated lifting capacity (overloading is strictly prohibited) and inspect the crane's steel cables, hooks, and pulley blocks for wear, broken wires, or deformation. Simultaneously, confirm the hydraulic system, braking device, and limiter are functioning properly.
  • Before operation, operators must monitor wind and waves in the working waters (suspend operation if wind force ≥ Level 6 or wave height ≥ 1.5m). Arrange personnel to clear obstacles within the operation radius. Additionally, check that the cargo is securely bound with symmetrically distributed lifting points (center of gravity deviation ≤ 5%), and it is essential to ensure anti-slip and anti-scratch protection at the contact points between slings and the cargo.

 

2. Practical Operation Methods (Prioritize Slowness and Stability)

  • Before test lifting, align the hook vertically with the center, tension the steel wire ropes first, then lift off the ground. Slowly raise the hook until the slings are taut and pause (cargo 10-20cm above the ground/deck). Check if the slings are under uniform stress, the cargo is balanced, and the brakes are effective.
  • After confirming no abnormalities in the test lift, hoist the cargo at a constant low speed (lifting speed ≤ 0.5m/s). Avoid sudden acceleration or stops. During the lifting process of the offshore crane, continuously monitor cable tension, hook condition, and whether the floating crane hull is inclined (inclination angle ≤ 3°).
  • Strictly prohibit oblique lifting or dragging ungrounded cargo; strictly prohibit adjusting lifting points or untying binding ropes during the lifting process.

 

Slewing Operation: Angle Control, Collision Prevention

 


1. Preparation Work

  • Determine the slewing range of the marine crane, mark warning lines on the ground/deck, and prohibit unauthorized personnel from entering the slewing area.
  • Confirm there are no obstacles (such as other equipment, dock facilities, or ship masts) in the slewing path, and maintain a safe distance (≥ 2m) from adjacent equipment.

 

2. Practical Operation Steps (Stable and Controllable)

  • After lifting the cargo to a safe height, slowly activate the slewing mechanism (slewing speed ≤ 0.8r/min). Avoid sudden direction changes or acceleration.
  • During slewing, continuously observe the cargo status (whether it is shaking or swinging excessively). If shaking occurs, stabilize the cargo by "inching the slewing" or slightly adjusting the lifting height.
  • Decelerate in advance before slewing to the target direction (deceleration distance ≥ 10% of the slewing angle) to prevent overshoot due to inertia; lock the slewing mechanism promptly after positioning.
  • Strictly prohibit forced slewing when the cargo is shaking violently; strictly prohibit slewing over personnel or important equipment; strictly prohibit slewing beyond the specified radius.

 

Lowering Operation: Precise Positioning, Impact Prevention


1. Hydraulic crane Pre-Lowering Preparation

  • First, confirm that the target position is flat, solid, and capable of bearing the cargo weight; ensure there is no standing water or oil at the landing point to avoid cargo sliding.
  • Establish clear communication signals (such as hand gestures, walkie-talkies) with ground commanders and confirm that the commander's position is safe.

 

2. Operation Key Points (Gentle Lowering and Precision)

  • Move the cargo directly above the landing point and slowly lower the hook (lowering speed ≤ 0.3m/s). Further decelerate when approaching the ground/deck (distance ≥ 30cm).
  • Fine-tune the cargo position according to the commander's signals to ensure the cargo fits the landing point smoothly without deviation or collision.
  • Lower the hook vertically at a slow pace. After the cargo is fully grounded, continue to loosen the slings. Only disconnect the slings from the cargo after confirming they are not under stress.
  • Strictly prohibit rapid lowering that causes the cargo to impact the ground; strictly prohibit untying slings before the cargo is fully grounded; strictly prohibit adjusting the landing point during the lowering process.


Essential Guidelines for Marine Crane Beginners

  • All operations must be performed by certified personnel. Strictly follow the floating crane operation manual and do not modify operational parameters without authorization.
  • Attend a safety briefing before the operation to clarify the work task, risk points, and emergency measures (such as handling procedures for equipment failures or uncontrollable cargo shaking).
  • Maintain full concentration during operation. Strictly prohibit operation under the influence of alcohol, fatigue, or any irregular practices; in case of emergencies, immediately stop operation, cut off the power supply, and report for handling.

 

Beginners can quickly get started by adhering to the principles of "Inspect First, Operate Slowly, Prioritize Communication". It is also recommended to complete initial practical training under the guidance of senior operators to ensure a balance between safety and efficiency.

 

 

 

Our Certificate 

 

 

factory2
BV1

  

SGS1 3

 

ISO