Comparison of Common Wear-Resistant Steel Materials for Hoppers

Jan 04, 2026

Leave a message

 The core requirements for port hoppers are wear resistance, impact resistance, and adaptability to material characteristics. NM360, NM450, and NM500 are all domestic quenched and tempered wear-resistant steel plates, with core differences reflected in hardness, wear resistance, mechanical strength, and application scenarios. Wear-resistant steel generally follows the rule that "the higher the model number, the higher the hardness and wear resistance, and the higher the cost. The selection of terminal-specific hoppers must be comprehensively judged based on port scenarios such as conveyed materials (e.g., ore, coal, sand, and gravel), operation intensity, and cost budget.

 

 

Comparison of Core Performance and Mechanical Parameters

 

Comparison Dimension

NM360

NM450

NM500

Key Conclusions

Brinell Hardness (HBW)

≥360

≥450

≥500

The hardness of NM500 is 38.9% higher than that of NM360 and 11.1% higher than that of NM450; hardness directly determines wear resistance.

Yield Strength (MPa)

≥900

≥800 (partial standards) / ≥950 (high standards)

≥1200

NM500 has significantly higher strength, suitable for high-stress working conditions; the yield strength of NM360 is better than that of conventional NM450.

Tensile Strength (MPa)

≥1100

≥1000 (conventional) / ≥1150 (high standards)

≥1500

The tensile strength of NM500 is 1.36 times that of NM360, with stronger deformation resistance.

Elongation (%)

≥15

≥10

≥8 (no unified standard, generally lower than the previous two)

The higher the model number, the lower the toughness; NM360 has the best impact resistance and fracture resistance.

Impact Toughness (-20℃, J)

≥30

≥24

≥20 (some products marked ≥27J/cm²)

NM360 is suitable for low-temperature and high-impact scenarios; NM500 needs to avoid high-frequency and high-impact.

Wear Resistance (Relative Value)

1.0 (benchmark)

1.5-2.0

2.5-3.0

The wear resistance of NM500 is 2.5-3 times that of NM360 and 1.25-2 times that of NM450.

 

 

Comparison of Processing Characteristics and Costs

 

Comparison Dimension

NM360

NM450

NM500

Key Conclusions

Welding Difficulty

Low: Conventional processes are sufficient, no special preheating required

Medium: Preheating to 80-150℃ is recommended

High: Preheating to 200-300℃ is required, special welding materials must be used, and heat preservation is needed after welding

NM360 has the best processing flexibility, while NM500 has extremely high requirements for processing technology

Cutting/Bending

Easy: Direct laser/plasma cutting is feasible, with good bending formability

Medium: Thermal deformation control is required for thick plate cutting

Difficult: Cracks are likely to occur during thick plate cutting, and preheating is needed for bending

For complex structures (such as special-shaped hoppers), NM360/NM450 is preferred

Repair Convenience

High: On-site surfacing repair is available after wear

Medium: Matching welding materials are required for surfacing

Low: Surfacing is difficult, and overall replacement is mostly required

NM360/NM450 is preferred for on-site maintenance in ports

2026 Reference Price (CNY/ton)

4800-5200 CNY/ton

5500-6200 CNY/ton

7200-8000 CNY/ton

The cost of NM500 is more than 50% higher than that of NM360, and NM450 has a medium cost-performance ratio

Total Life Cycle Cost

Medium: Frequent replacement/repair is required, resulting in high long-term costs

Low: Balances service life and cost, with the best cost-performance ratio

Medium-Low: High initial investment but long service life, suitable for high-wear working conditions

NM500 is more cost-effective in the long run for high-frequency operation scenarios, and NM450 is selected for intermittent operation

 

Comparison of Application Scenarios (Focus on Port Field)

 

Comparison Dimension NM360 NM450 NM500

Core Advantages

Good toughness, easy processing, low cost, suitable for medium-low wear and high-impact scenarios.

Balanced wear resistance and toughness, high cost-performance ratio, making it the mainstream choice for ports.

Ultra-high wear resistance and high strength, suitable for extreme wear working conditions.

Port-Specific Applications

① Hopper liners and chutes for low-wear materials such as coal, grain, and chemical fertilizers;

② Ship unloader hoppers (needing to withstand the impact of falling materials);

③ Conveyor rollers and slightly worn conveyor belt liners;

④ Outdoor equipment components in low-temperature ports (e.g., northern winters).

① Hoppers and crusher liners for medium-wear materials such as sand, gravel, and limestone;

② Jib liners and funnels of port stacker-reclaimers;

③ Conveyor baffles and guide plates in bulk cargo terminals;

④ Wear-resistant components after conventional anti-corrosion treatment in coastal ports (balancing strength and processability).

① Hopper liners and crusher hammers for high-hardness materials such as iron ore, nickel ore, and basalt;

② Key wear-resistant components of heavy-duty ship unloaders and stackers operating 24/7;

③ Bulldozer bottom plates and loader blades requiring thick specifications (20-60mm);

④ Liners of chutes and discharge pipes with extremely high wear frequency.

Supplementary Note

It is also commonly used for slightly worn components in auxiliary port facilities such as thermal power plants and cement plants.

This model is the first choice for general wear-resistant components in coal yards and mining machinery.

High-frequency impact from large bulk materials should be avoided, otherwise cracks are likely to occur.

 

 

Core Selection Recommendations

 

How To select  a port-specific hopper?

 

Consider material abrasiveness: Choose NM360 for low-abrasion materials (coal, grain); NM450 for medium-abrasion materials (sand and gravel); NM500 for high-abrasion materials (ore).

 

Consider impact intensity: Choose NM360/NM450 for high impact (e.g., materials falling from heights); choose NM500 for low impact.

 

Consider processing requirements: Choose NM360/NM450 for special-shaped structures or on-site welding/repair; choose NM500 for simple structures or thick plate requirements.

 

Consider cost budget: Choose NM360 for a limited budget and intermittent operation; choose NM450 for cost-performance pursuit and continuous operation; choose NM500 for high-frequency, high-wear and long-term use.

 

Special Port Recommendations: In coastal salt spray environments, all three models require anti-corrosion coating; for northern low-temperature ports, NM360/NM450 is preferred to avoid low-temperature brittleness and cracking of NM500

port hopper 7