Deep Cleaning Techniques for Marine Cranes: Thorough Removal of Stubborn Dirt and Salt Deposits

Jul 08, 2025

Leave a message

 

Cleaning serves as the foundation of the "Golden Three-Step Method" of daily maintenance for marine cranes. Deep cleaning is a crucial step for removing stubborn dirt and salt deposits and extending the equipment's lifespan. Mastering professional techniques can significantly enhance the cleaning effect when dealing with complex contaminants such as high salt fog and heavy oil stains.

 

I. Preparation for Deep Cleaning 

 

Tool Preparation

Physical Cleaning Tools: High-pressure cleaners (pressure: 8 - 12MPa, equipped with fan-shaped nozzles), stainless steel wire brushes (for seams and other narrow areas), nylon brushes (to protect the coating surface), and vacuum suction equipment (for debris removal).

 

Chemical Cleaning Tools: Acid and alkali-resistant gloves, safety goggles, chemical protective aprons, and spray bottles (for uniform application of cleaning agents).

 

Cleaning Agent Selection

Salt-Removing Agents: Select weak alkaline salt-removing agents (pH 9 - 10) containing surfactants, such as EDTA tetrasodium solution, which can quickly dissolve salt crystals.

 

Oil Stain Cleaners: For heavy oil stains, use biodegradable solvents, such as environmentally friendly cleaners mainly composed of citrus extracts. These cleaners can penetrate and dissolve stubborn stains like mineral oils and lubricating greases.

 

**Rust Preventive Agents**: After cleaning, promptly apply water-based rust preventives to form a temporary protective film and prevent rapid metal oxidation in a humid environment.

 

 II. Deep Cleaning Techniques for Different Components

 

(I) Deep Cleaning of Metal Structures

Pre-rinse: Use high-pressure fresh water to pre-rinse large-area structures such as booms and bases at a 45° angle, removing surface dust and marine organisms. Pay special attention to flushing areas prone to salt accumulation, such as water-collecting grooves and welds.

 

Agent Treatment: Dilute the salt-removing agent at a ratio of 1:10 and spray it on stubborn salt stains. Wait 5 - 10 minutes for the agent to fully penetrate and soften the salt crystals.

 

Mechanical Assistance: For areas difficult to rinse, such as seams and bolt holes, gently scrub with a stainless steel wire brush. Use vacuum suction equipment to remove dissolved salt and debris promptly to avoid secondary contamination. **Secondary Rinsing**: Thoroughly rinse off the remaining cleaning agent with high-pressure fresh water, ensuring that the surface pH value is neutral (pH = 7).

 

(II) Deep Cleaning of Moving Parts

Dismantling and Cleaning: For detachable parts such as pulleys and drums, dismantle them and soak them in an oil stain cleaner solution (temperature controlled at 40 - 50°C) for 30 minutes. Then, use an ultrasonic cleaner to vibrate for 15 minutes to remove internal oil stains and sediment thoroughly.

 

Non-dismantling Cleaning: For non-detachable gear meshing areas, use the thin-stream mode of a high-pressure cleaner (pressure: 6 - 8MPa) to rinse alternately from both sides of the gear teeth. Use a long-handled nylon brush to clean the dirt in the gear grooves.

 

(III) Deep Cleaning of Electrical and Hydraulic Systems

Electrical Systems: Turn off the power and disconnect all connections. Use dust-free cloths dipped in absolute ethanol to carefully wipe the circuit boards and terminal blocks inside the control cabinet, removing salt crystals and dust. Precision components such as sensors and cameras use nitrogen blowing (0.2 - 0.3MPa) to avoid water residue.

 

Hydraulic Systems: Use special hydraulic oil wiping cloths to clean the interfaces of hydraulic pipelines and piston rods of cylinders. For oil sludge formed by leakage, apply oil stain cleaners locally and then wipe repeatedly with dust-free paper until the surface is free of oil stains.

 

Protective Measures After Deep Cleaning

 

Coating Repair: Inspect the metal surface coating. For areas with damage exceeding 10cm², sand according to NORSOK standards (surface roughness Ra 25 - 50μm), spray epoxy zinc-rich primer (dry film thickness 80 - 100μm), and apply polyurethane topcoat (dry film thickness 150 - 200μm).

 

Rust Prevention: Evenly spray volatile rust preventives on the cleaned metal surface, especially in hard-to-reach corners and crevices, to form a volatile rust prevention layer.

 

Drying Treatment: Use a hot air blower (temperature < 60°C) to dry the cleaned areas, ensuring no water residue, especially in areas prone to moisture, such as electrical junction boxes and hydraulic valve groups.

 

 
Our factory & Equipment
 

The offshore cranes we produce comply with ISO crane use specifications and are certified by major classification societies. If you need any offshore cranes, please get in touch with us!

Email:megyhu@yfm-crane.com

WhatsApp:+8613886003497

telescopic knuckle boom crane 7
Telescopic Knuckle boom crane
TELESCOPIC BOOM CRANE 6
telescopic boom crane
davit crane
davit crane