Maintenance Adjustments in High-Temperature Environments
Hydraulic System: For hydraulic cranes, select high-temperature adaptive hydraulic oil (viscosity index ≥ 160) and shorten the hydraulic oil replacement cycle (20% shorter than the conventional cycle); Marine cranes need to regularly clean the hydraulic oil radiator and install a temperature monitoring and alarm device. When the oil temperature exceeds 85°C, it will automatically shut down for cooling to avoid aging and failure of hydraulic component seals due to high temperatures.
Electrical System: The control cabinet of deck cranes must be equipped with a forced ventilation and heat dissipation device, and high-temperature-resistant electrical components (temperature resistance ≥ 125°C) should be used. Marine cranes need to check whether the cable insulation layer is overheated and softened, and measure the temperature rise of the electrical system every two weeks to ensure it does not exceed the rated value.
Metal Structural Parts: Strengthen temperature monitoring of stressed parts such as the boom and slewing bearing of marine cranes, to avoid local overheating caused by direct sunlight. A reflective and heat-insulating coating can be applied to the metal surface to reduce the temperature difference stress of structural parts.
Maintenance Adjustments in High-Humidity Environments
Lubrication System: All lubrication points of hydraulic cranes must use water-resistant grease (such as water-based grease) and increase the filling frequency (once a week); Marine cranes should add moisture-proof additives to the grease to prevent lubrication failure due to moisture intrusion, and regularly check for emulsification in lubricated parts.
Electrical System: Upgrade the sealing of motors and control cabinets of deck cranes (to IP65 protection level) and install dehumidification devices (such as moisture-proof heating plates); Marine cranes need to maintain the relative humidity in the electrical box ≤ 60%, and use an insulation meter to test the insulation resistance of electrical equipment monthly to ensure it is ≥ 1 MΩ.
Metal Surfaces: Apply anti-rust oil to deck cranes' non-painted metal parts (such as bolts and pins), promptly touch up damaged paint layers, and regularly purge moisture in equipment gaps with dry compressed air.
Maintenance Adjustments in Corrosive Environments (Salt Spray, Chemical Corrosion)
Structural Part Protection: Marine cranes must undergo sandblasting to remove rust and then be painted with a heavy-duty anti-corrosion coating (dry film thickness ≥ 200 μm); Key parts of deck cranes (such as welds and connectors) adopt zinc block sacrificial anode protection. Check the coating integrity quarterly and repair damaged areas.
Key Components: For vulnerable parts such as pins and bolts of hydraulic cranes, use seawater corrosion-resistant materials (such as 316 stainless steel). The hydraulic pipelines of marine cranes adopt double-layer anti-corrosion treatment (galvanized inner layer + anti-corrosion paint sprayed outer layer). Regularly conduct salt spray tests on exposed metal parts to ensure the corrosion rate is ≤ 0.05 mm/year.
Adaptation of Maintenance Tools: When maintaining deck cranes, use salt spray-proof special tools (such as marine-grade torque wrenches and anti-corrosion coating detectors). After each maintenance, desalt the tools (rinse with fresh water + dry) and store them in a nitrogen-filled, moisture-proof toolbox to avoid tool corrosion affecting maintenance accuracy.
Comprehensive Response Strategies
Establish a special environment maintenance ledger to record marine cranes' operating parameters and maintenance frequencies in high-temperature, high-humidity, and corrosive environments. Dynamically adjust the maintenance cycle based on equipment operation time and environmental parameters.
Provide special training for operators to enable them to master the skills of judging equipment abnormalities of hydraulic cranes in special environments. Equip deck cranes with environmental monitoring instruments (such as thermometers, hygrometers, and salinometers) to monitor operating environment parameters in real-time and make maintenance preparations in advance.
Conduct comprehensive equipment inspections regularly (once every six months), including non-destructive testing of marine crane structural parts, pollution analysis of hydraulic crane hydraulic systems, and insulation testing of deck crane electrical systems. Timely detection of potential faults caused by environmental erosion ensures the reliable operation of various cranes in special environments.





