Offshore crane electrical troubleshooting: control failure troubleshooting steps

Jun 23, 2025

Leave a message

1. Safety and preparation before operation

 

  • (i) Safety protection measures Offshore cranes are in a harsh environment of high humidity, salt spray, and vibration. Strict safety regulations must be followed before maintenance. First, disconnect the main power supply of the marine crane through the main distribution panel in the engine room, and use a tester that meets the marine explosion-proof standards to test each electrical circuit to ensure that there is no residual voltage. Set a double locking device at the power switch and hang a warning sign. At the same time, arrange for a special person to monitor to prevent the wrong power supply. Maintenance personnel must wear life jackets and non-slip shoes and use anti-fall safety ropes to fix themselves to a safe point on the deck if high-altitude operations are involved.

 

  • (ii) Equipment and tool preparation: Prepare professional testing equipment suitable for marine environments, such as waterproof multimeters, marine megohmmeters, and explosion-proof infrared thermal imagers. At the same time, technical information such as the ship crane electrical schematics, PLC program lists, and inverter parameter manuals must be carried. Key spare parts, such as marine-grade contactors, sealed relays, and moisture-proof sensors, need to be reserved in advance to avoid delays in maintenance due to difficulties in replenishment at sea.

 

2. Detailed analysis of fault phenomena​

 

  • (i) Multi-dimensional fault records​ Control failure may take many forms and need to be recorded in detail: when the operating handle does not respond, observe whether there is an alarm code on the dashboard; if the equipment malfunctions, record the direction and amplitude of the action; for intermittent failures, count the frequency of failures and working conditions (such as when lifting heavy loads). For example, when a boat crane was operating in strong winds and waves, the boom mechanism suddenly lost control, and it was necessary to synchronously record environmental parameters such as wind speed and hull tilt angle at the time. ​

 

  • (ii) Preliminary appearance inspection​ Focus on checking whether the sealing strips of the electrical cabinet are aging and cracking, and whether there is condensation and water accumulation inside; check whether the cable connectors are rusted and loose, especially the through-cabin cables between the deck and the engine room, and check whether their explosion-proof sealing connectors have failed. Observe whether the contactor contacts have poor contact caused by salt spray crystallization, and whether the status of the PLC module indicator light is abnormal. ​

 

  • 3. Systematic troubleshooting process

(i) In-depth inspection of the power supply system

 

Inspection items Operation method Specific fault points in the marine environment
Main power supply Use a marine multimeter to measure the 690V/440V primary circuit voltage and check the neutral point grounding resistance (should be ≤1Ω) Seawater corrosion causes rust on the grounding copper busbar and salt spray short circuit of the transformer
Emer. gency power supply switching Simulate the primary power failure and test the automatic start-up function of the UPS or diesel emergency generator Batt. Every pack leakage is caused by moisture and oxidation of the emergency contactor contacts
Lightning protection system Check the status of the surge protector (SPD) and measure the conductivity of the grounding device Brea. Grounding of the SPD module caused by a lightning strike and seawater corrosion of the lightning protection grounding electrode

 

 

(ii) Troubleshooting of complex control circuits.

1. Redundant control system detection: Modern marine cranes often use a dual PLC hot standby system. Programming software must compare the I/O data synchronization status of the master and enslaved person PLCs to check the reliability of the contacts of the redundant switching module.

2. Sensor and actuator linkage test:

Lifting weight limiter: Use standard weights to calibrate the pressure sensor and check whether its 4- 20mA signal output is stable to prevent signal drift caused by salt spray intrusion.

  • Angle encoder: During the boom amplitude change process, an oscilloscope monitors the encoder pulse signal to check for loose code discs caused by vibration. 

3. Frequency conversion drive system diagnosis: Use special debugging software to read the inverter fault code and detect the IGBT module temperature (normal ≤80℃) to prevent overheating protection caused by insufficient sea breeze cooling.

  •  

3. Special inspection of actuators.

 

  • Wire rope drum motor: Measure the motor's insulation resistance (it should be ≥10MΩ), check the wear of the carbon brushes, and prevent the carbon brushes from sparking due to sea turbulence. 

 

  • Hydraulic proportional valve control: Detect the output voltage of the proportional amplifier, manually adjust the valve core opening, and check for valve jamming caused by hydraulic oil contamination.

 

4. Special troubleshooting skills​

 

  • (I) Environmental adaptability fault repair​ . For circuit board failures caused by salt spray corrosion, a three-proof paint spraying process is used to protect the repaired PCB board; for cable damage, a marine-grade waterproof junction box and heat shrink tubing are used. ​

 

  • (II) Intelligent diagnostic assistance​ : Use the remote monitoring system to retrieve the hydraulic marine crane operation log and analyze the parameter curves before and after the fault occurs. For example, historical data on the torque limiter determines whether the control lock is caused by overload. ​

 

5. Repair verification and maintenance upgrade

 

  • (I) Full-condition test. Under no-load, half-load, and full-load conditions, test the lifting, luffing, and slewing actions of the marine crane respectively, record the operating current and voltage fluctuation range of each mechanism, and ensure that it is within ±10% of the rated value.

 

  • (II) Preventive maintenance plan: Formulate a quarterly inspection plan, focusing on checking the working status of the dehumidification device and heating belt of the electrical cabinet; conduct cable insulation withstand voltage test once a year, replace aging marine cables; regularly upgrade the PLC program version and optimize the control logic.

 

modular-1
One-stop port machinery sales and service

 Ifima Technology (Shanghai) Co., Ltd. is a port machinery and equipment manufacturer with 13 years of experience in China. With ISO 9001, CE, and GOST certifications and exports to more than 50 countries, we provide reliable marine machinery guaranteed by R&D innovation and strict quality control.