The stability of the hydraulic system is vital to the daily operation of marine cranes, port cranes, deck cranes, offshore cranes, and other equipment. Hydraulic leakage not only wastes hydraulic oil but may also lead to equipment failures and pose a threat to operational safety. Mastering methods for quickly locating and repairing leak points is the key to ensuring the efficient operation of various marine cranes.
I. Quick Location of Leak Points
- (I) Visual Inspection For equipment such as marine cranes and port cranes that are exposed to the aquatic environment for long periods, after the marine crane is stopped and the hydraulic system is depressurized, a comprehensive inspection should be carried out along hydraulic pipelines, joints, hydraulic cylinders, and other components. Pay special attention to areas prone to corrosion, such as the lower part of pipelines on deck cranes frequently splashed by waves and the gaps of joints on offshore cranes. Carefully observe for signs of oil stains, drips, or mist. These visible leakage signs can often help maintenance personnel quickly identify the general area of the leak.
- (II) Pressure Testing Start the hydraulic system of marine cranes and keep it running at a low load. A pressure detector will test the pipeline pressure section by section. If there is a sudden drop in pressure during a specific section of the test, it indicates that there is a leakage problem in this area. For concealed leakage parts that are difficult to observe directly, soapy water can be applied to the surface of the pipeline, and the location where bubbles are generated is the exact leak point. This method applies to the hydraulic system inspection of various port and deck cranes.
- (III) Dye Detection: Add a fluorescent tracer to the hydraulic systems of equipment such as marine and offshore cranes. Let the equipment run for some time to allow the tracer to mix with the hydraulic oil. Then, an ultraviolet lamp irradiated the suspicious parts of the hydraulic system. The leak points will show bright fluorescence. This method can accurately locate tiny leak points and effectively solve the problem of difficult detection of minor leaks by conventional methods.
II. Leak Repair Measures
- (I) Joint Leakage If aging seals cause joint leakage in marine and port cranes' hydraulic systems, immediately replace them with fluoro rubber or nitrile rubber seals with excellent seawater corrosion resistance. If loose threads cause the leakage, use a torque wrench to retighten according to the standard torque and apply thread-locking adhesive to prevent the joints from loosening again, ensuring the sealing of hydraulic joints of deck cranes, offshore cranes, and other equipment.
- (II) Pipeline Leakage For minor cracks in the hydraulic pipelines of various marine cranes, temporary plugging can be carried out with pressure-resistant leakage-blocking tape to ensure the safe return of the equipment to the port. After returning to port, replace the pipeline with a new one promptly. In case of - ongoing damage to the pipeline, directly cut off the damaged part and install a quick-connect fitting to connect the new pipeline. At the same time, it is essential to carry out anti-corrosion treatment on the new pipeline to improve its service life in the marine environment.
- (III) Hydraulic Cylinder Leakage Disassemble the hydraulic cylinders of equipment such as marine cranes and port cranes. Carefully check the piston and guide sleeve seals for wear, and replace the damaged seals promptly. If scratches are found on the inner wall of the cylinder barrel, minor scratches can be repaired by grinding, while severe scratches require the replacement of the cylinder barrel. After reassembly, a sealing test must be carried out on the hydraulic cylinder to ensure that it restores normal working performance and meets the operation requirements of deck cranes, offshore cranes, and other equipment.
III. Prevention and Maintenance
- Regularly inspect the condition of seals in the hydraulic systems of equipment such as marine cranes and port cranes. Based on the equipment's usage frequency and environmental conditions, replace the seals of vulnerable parts in advance to prevent potential problems.
- Strengthen the monitoring of hydraulic oil quality and establish a strict hydraulic oil inspection system to prevent seawater contamination from accelerating seal aging and ensure the cleanliness and stability of the hydraulic system.
- During each Maintenance of marine cranes, carry out anti-corrosion spraying on hydraulic pipelines and joints to enhance their corrosion resistance, extend the service life of key components of the hydraulic system, and ensure the stable operation of deck cranes, offshore cranes, and other equipment in the complex marine environment.
Our clients
our clients from all over the world









